Chrysler Suspension Front Wheel Bearing


View 87 Suspension Front Wheel Bearing Safety Reports

Chrysler Lebaron 1989
Daimlerchrysler Corporation
Safety incident date:
Mar 06, 1995
Location:
San Clemen, CA

wheel bearings failed. *skd

0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):1C3XJ45JXKG. Vehicle was not using Cruise Control.

Chrysler Sebring 1995
Daimlerchrysler Corporation
Safety incident date:
Apr 08, 1996
Location:
Rutland, VT

defective rear wheel bearing caused wheel to wobble/fire. *dsh

Vehicle was on fire. 0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):4C3AU425Y5S. Vehicle was not using Cruise Control.

Chrysler Lebaron 1991
Daimlerchrysler Corporation
Location:
Sagamore Hills, OH

bushings replaced.

0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):1C3YJ4530MG. Vehicle was purchased on Feb 23, 1991. Vehicle was not using anit-lock brakes. Vehicle was using Cruise Control.Fuel System:N/A. Fuel type: gas. Chrysler LEBARON 1991 Suspension Front Wheel Bearing Transmission Type: AUTO.

Chrysler Lebaron 1992
Daimlerchrysler Corporation
Location:
Bayberry, NY

wheel bearings failed, because they were enclosed in plastic containers.

0 person(s) died.Vehicle Identification Number (VIN):3C3XA4636NT. Vehicle was using anit-lock brakes.Vehicle was using Cruise Control.Chrysler LEBARON 1992 Drive type:FWD. Fuel System:N/A. Fuel type: gas. Chrysler LEBARON 1992 Suspension Front Wheel Bearing Transmission Type: AUTO.

Chrysler Lhs 1995
Daimlerchrysler Corporation
Location:
Everett, MA

front wheel bearings failed.

0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2C3HC56F35H. Vehicle was purchased on Apr 01, 1995. Vehicle was using anit-lock brakes.Vehicle was using Cruise Control.Chrysler LHS 1995 Drive type:FWD. Fuel type: gas. Chrysler LHS 1995 Suspension Front Wheel Bearing Transmission Type: AUTO.

Chrysler Concorde 1993
Daimlerchrysler Corporation
Location:
Chalfont, PA

wheel bearing was replaced, eliminating front end vibration. rear view mirror fall off twice, once while driving almost causing an accident. front brakes or actually the tractioned control unit malfunction causing the brakes to stay on intermittently from a standing start under normal dry road condition. air conditioner leaked fumes into the interior causing a refrigerant odor, replace o rings. ignition switch replace twice, due to key could be taken out of the ignition whild driving, but at rest position the key could not be removed. car can suddenly violently downshifts, without warning , while driving at higher

0 person(s) were injured. 0 person(s) died.Original Owner. Vehicle was using anit-lock brakes.Vehicle was using Cruise Control.Chrysler CONCORDE 1993 Drive type:FWD. Fuel System:N/A.

Chrysler Cirrus 1995
Chrysler Group Llc
Safety incident date:
Sept 05, 1997
Location:
Lynwood, CA

stabilizer bar, ball joint-sway bar link and bushing failed causing noise.

Vehicle Identification Number (VIN):1C3EJ56HXSN. Vehicle was purchased on Oct 05, 1995. Vehicle was not using Cruise Control.

Chrysler Concorde 1996
Chrysler Group Llc
Location:
Houston, TX

the inner tie rods, bushings and the steering gear failed causing extreme vibrations while driving. *mjs

Vehicle Identification Number (VIN):2C3HD56T8TH. Original Owner. Vehicle was purchased on Jan 23, 1996. Vehicle was using Cruise Control.Chrysler CONCORDE 1996 Drive type:FWD. Fuel System:N/A. Fuel type: gas. Chrysler CONCORDE 1996 Suspension Front Wheel Bearing Transmission Type: AUTO.

Chrysler Concorde 1996
Chrysler Group Llc
Location:
Lewleox, IL

pe99031; bushing that holds track assembly has failed ,almost feels that power steering goes to maunal steering. please provide further information.*ak

Original Owner. Vehicle was using anit-lock brakes.Vehicle was using Cruise Control.

Chrysler Town And Country 1999
Daimlerchrysler Corporation
Location:
Covongton, GA

the wheel bearing were defective and caused noise. nlm

Vehicle Identification Number (VIN):1C4GP54L6XB. Vehicle was not using Cruise Control.

Chrysler Lhs 1996
Daimlerchrysler Corporation
Location:
Bristol, FL

failed bushings cause steering problems. no replacement part available!*ak

Vehicle Identification Number (VIN):2C3HC56F2TH. Vehicle was purchased on July 01, 1998. Vehicle was using anit-lock brakes.Vehicle was using Cruise Control.Chrysler LHS 1996 Drive type:FWD. Fuel System:N/A. Fuel type: gas.

Chrysler Concorde 1998
Daimlerchrysler Corporation
Safety incident date:
Jan 16, 2001
Location:
Palos Park, IL

while driving could hear noise coming from under vehicle, and had taken vehicle to dealer. they found out that noise came from the bushings. *ak

0 person(s) were injured. 0 person(s) died.Vehicle was not using anit-lock brakes. Vehicle was not using Cruise Control. Vehicle Speed: 0 mph.

Chrysler Concorde 1994
Daimlerchrysler Corporation
Safety incident date:
Dec 07, 2000
Location:
Franklin, VA

front suspension bushings have worn prematurly and consistantly with this car. is there a reason for this. we maintain tires, alignments, etc. the front tirod bushings seem to be consistantly being replaceed. the bushings were replaced about 12,000 miles ago. the car lost traction in snow and spun out. when the insurance and dealer inspected the car, they replaced a blown transmission line, and indicated the front bushings were dry rotted and needed to be replaced. i have documentation of lube/oil changes for this car. can you give guideance on this problem with which to address the dealer.*ak

Vehicle Identification Number (VIN):2C3HD56FOSH. Original Owner. Vehicle was purchased on June 01, 1994. Vehicle was using anit-lock brakes.Vehicle was using Cruise Control.Chrysler CONCORDE 1994 Drive type:FWD. Fuel System:N/A. Fuel type: gas.

Chrysler Sebring 1996
Daimlerchrysler Corporation
Safety incident date:
Oct 13, 2000
Location:
Chippewa Falls, WI

front suspension would wearout excessively. front wheel bearings had to be replaced. also, lower left ball joint/ outer tie rod end/ sway bar link, and bushings were replaced by mechanic. in addition, head gaskets were leaking water and oil, and they were replaced.*ak *slc

Vehicle Identification Number (VIN):3C3EL45X8TT. Vehicle was purchased on Nov 20, 1998. Vehicle was using anit-lock brakes.Vehicle was using Cruise Control.Chrysler SEBRING 1996 Drive type:FWD. Fuel System:N/A. Fuel type: gas. Chrysler SEBRING 1996 Suspension Front Wheel Bearing Transmission Type: AUTO.

Chrysler Town And Country 2000
Daimlerchrysler Corporation
Safety incident date:
Nov 12, 1999
Location:
Herman, MN

grease is all over body of vehicle. someone told consumer it was front wheel bearing. *ak numerous attempts had been made to fix the grease problem, but the problem continues to exist. the consumer was concerned about safety. *yh

0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):1C4GP44G3YB. Original Owner. Vehicle was purchased on Oct 15, 1999. Vehicle was using anit-lock brakes.Vehicle was using Cruise Control.Chrysler TOWN AND COUNTRY 2000 Drive type:4WD. Fuel System:N/A. Fuel type: gas. Chrysler TOWN AND COUNTRY 2000 Suspension Front Wheel Bearing Transmission Type: AUTO. Vehicle Speed: 0 mph.

Chrysler Sebring 1995
Daimlerchrysler Corporation
Safety incident date:
Feb 29, 2000
Location:
Omaha, NE

while driving consumer hard a rubbing noise, like brakes were dragging. took vehicle to dealer, and they said it was wheel bearing hub. consumer could see one wheel bearing assembly failing, but both going at the same time, he felt it was not normal. *ak

0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):4C3AU52N5SE. Vehicle was not using anit-lock brakes. Vehicle was not using Cruise Control. Vehicle Speed: 0 mph.

Chrysler Sebring Coupe 1996
Chrysler Group Llc
Location:
Hiram, OH

consumer states front wheel bearing went bad twice, and the rear wheel bearing also went out twice.*jb

Vehicle was not using Cruise Control.

Chrysler New Yorker 1995
Daimlerchrysler Corporation
Safety incident date:
May 04, 2001
Location:
Rimrock, AZ

steering noise when turning wheel left to right, bushings are bad and rack and pinion needs replaceing according to mechanic said such wear is unusually for car with such low miles - dealer, maker aware of problem said it will not do anything unless a recall is forced on them - lose of steering is a safety issue

0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2C3HC46F0SH. Vehicle was purchased on Jan 01, 2000. Vehicle was using anit-lock brakes.Vehicle was using Cruise Control.Chrysler NEW YORKER 1995 Drive type:FWD. Fuel System:N/A. Fuel type: gas.

Chrysler Town And Country 2001
Daimlerchrysler Corporation
Safety incident date:
Sept 03, 2001
Location:
Morris, IL

washer and nut came off the front wheel while consumer was going 15mph. abs light came on as a warning, and vehicle made a grinding noise. consumer got home, and found caliper was the only thing holding the wheel. pin was not put in during manufacturing. *ak consumer states a flat washer and flat nut (not a lock nut) were used, also there is not a crown nut, nor a cotter pin installed. dealer stated the bearing had come loose from the hub and failed, probably due to insufficient torque on the flat washer and nut. *slc

Vehicle Identification Number (VIN):2C8GP44361R. Original Owner. Vehicle was purchased on Aug 15, 2001. Vehicle was using anit-lock brakes.Vehicle was using Cruise Control.Chrysler TOWN AND COUNTRY 2001 Drive type:FWD. Fuel System:N/A. Fuel type: gas. Chrysler TOWN AND COUNTRY 2001 Suspension Front Wheel Bearing Transmission Type: AUTO. Vehicle Speed: 15 mph.

Chrysler Town And Country 2001
Daimlerchrysler Corporation
Safety incident date:
Sept 03, 2001
Location:
Morris, IL

while driving, there was a scraping noise in the front right wheel, the grinding then became worse and the steering wheel was vibrating, and the abs flashed a couple times and went out as the vehcile was going straight, consumer pulled into the driveway and smelled something hot and felt the front right and tire which was hot and the wheel could be shaken very readily, consumer pulled the front right wheel off and a flat washer and regulator nut fell from the front hub, the vehicle was towed and consumer was informed that the parts that were needed were not available and that the bearing dome was loose from the hub, which probably failed due to insufficent torque.*jb

Original Owner. Vehicle was purchased on Aug 15, 2001. Vehicle was not using anit-lock brakes. Vehicle was not using Cruise Control. Vehicle Speed: 20 mph.


Common Chrysler Problems

View Suspension Front Wheel Bearing Safety Reports

Electrical System (2733 Reviews)

Power Train:automatic Transmission (1600 Reviews)

Engine (1314 Reviews)

Engine And Engine Cooling (1217 Reviews)

Air Bags (1181 Reviews)

Engine And Engine Cooling:engine (1144 Reviews)

Steering (1101 Reviews)

Power Train (1019 Reviews)

Service Brakes, Hydraulic:antilock (1011 Reviews)

Vehicle Speed Control (958 Reviews)

Fuel System, Gasoline (799 Reviews)

Air Bags:frontal (712 Reviews)

Service Brakes, Hydraulic (704 Reviews)

Suspension (665 Reviews)

Structure (620 Reviews)

Exterior Lighting (571 Reviews)

Unknown Or Other (515 Reviews)

Engine And Engine Cooling:engine:gasoline (477 Reviews)

Fuel/propulsion System (459 Reviews)

Structure:body (438 Reviews)


footer